User Guide
MaxiFirm Pro
MaxiFirm Pro
Complete Instructions
Everything you need to use your device safely, effectively, and with confidence.
How It Works
The MaxiFirm Pro is an electric vacuum erection device (VED). It creates negative air pressure inside the cylinder, drawing blood into the erectile tissue to produce a firm, natural erection. The electric motor automates suction, giving you precise pressure control at the touch of a button.
What's in the Box
| Item | Purpose |
|---|---|
| Acrylic cylinder / tube | Fits over the penis to create the vacuum chamber |
| Electric pump unit | Motorized suction control — attaches to the cylinder |
| Silicone seal / gasket | Creates an airtight seal against the body |
| Constriction rings (1–3 sizes) | Placed at the base of the penis after pumping to maintain erection |
| USB charging cable | Recharges the electric pump unit |
Before First Use
1
Charge the Device
Connect via USB and charge for 1–2 hours until the indicator light turns solid. Never use while charging.
2
Clean All Parts
Wash the cylinder, seal, and rings with warm water and mild antibacterial soap. Rinse well and air dry completely.
3
Learn the Controls
- Power — on/off
- + — increase suction
- − — decrease suction
- Release valve — releases all pressure instantly
4
Do a Test Run
Block the open end with your palm and press power. Confirm suction builds and the release valve works correctly.
Step-by-Step Usage Guide
1
Prepare Your Body
- You may optionally trim or shave pubic hair at the base of the penis — this can help the silicone seal sit flush against the skin for a better airtight seal, but is not required.
- You may apply a warm towel to the area for 1–2 minutes to increase blood flow before starting.
2
Apply Lubricant
- Apply a generous amount of water-based lubricant around the rim and silicone gasket of the cylinder's open end.
- You can also apply lubricant directly to the penis before inserting.
- Do not use oil-based or silicone-based lubricant — these degrade silicone components over time.
✨
Enhance your results with Intimacy Enhancement Gel
Its clinically-formulated blend of L-Arginine and botanical extracts helps boost blood flow and increase firmness alongside the pumping action — no pills, no prescriptions.
Get Intimacy Enhancement Gel →
Get Intimacy Enhancement Gel →
3
Load the Constriction Ring (Optional)
- If you plan to use a constriction ring afterward, load it onto the cylinder now before inserting your penis.
- Stretch the ring over the open end of the tube so it sits near the base of the cylinder.
4
Insert and Seal
- Insert your flaccid or semi-erect penis fully into the cylinder.
- Press the open end firmly and evenly against your pubic area. The silicone gasket should form a complete, gap-free seal.
- Hold the cylinder steady with one hand throughout the session.
5
Begin Pumping
- Press the power button to start the motor.
- Begin at the lowest suction setting and press + to increase gradually over 30–60 seconds.
- You should see the penis expanding and filling with blood inside the clear cylinder.
6
Hold at Your Target Pressure
- Once you reach a comfortable, firm level of suction — stop increasing.
- Hold at that level for 3–5 minutes per session.
- It should feel like a firm, even pulling pressure. It should never hurt.
⚠️
If you feel sharp pain, tingling, or numbness — press the release valve immediately.
7
Release Pressure Safely
- Press the quick-release valve to equalize pressure before removing the cylinder.
- Once pressure is fully released, gently remove the cylinder.
⚠️
Never pull the cylinder away without releasing the vacuum first. Doing so can cause bruising or vascular injury.
8
Apply the Constriction Ring (Optional)
- Before removing the cylinder, slide the pre-loaded ring off the cylinder base onto the base of the penis.
- Then release pressure and remove the cylinder.
- The ring helps maintain erection by slowing blood outflow.
⚠️
Remove the constriction ring within 30 minutes. Never sleep with it on.
Recommended Usage Schedule
| Goal | Sessions per Week | Duration per Session |
|---|---|---|
| Erectile dysfunction support | 5–7 days | 10–15 min |
| Post-surgery rehabilitation | Daily (as directed by doctor) | 10 min |
| General sexual wellness | 3–4 days | 5–10 min |
| Pre-intercourse use | As needed | 5–10 min |
💡
Tip for beginners: Start with just 5 minutes at low pressure for the first week. Gradually increase duration and pressure as your body adapts.
Charging & Battery
- Charge via USB before first use and whenever suction feels weaker than usual.
- A full charge typically lasts multiple sessions.
- Store with some charge remaining — avoid storing fully depleted.
- Do not use while charging.
Cleaning After Every Use
- Disconnect the pump unit from the cylinder.
- Wash the cylinder, seal, and rings with warm water and mild antibacterial soap. Fill the cylinder partway with soapy water, cover both ends, and shake gently — then rinse thoroughly with clean water.
- Wipe the electric pump unit with a damp cloth only — never submerge it in water.
- Rinse all non-electric parts thoroughly and allow to air dry completely before storing.
- Store in a clean, dry location away from direct sunlight and heat.
🧴
Using Intimacy Enhancement Gel?
It rinses cleanly from all silicone parts — no residue, no buildup. Safe to use every session.
Learn more →
Learn more →
Safety Rules
✅ Do
- Start at low pressure and build gradually
- Use water-based lubricant or Intimacy Enhancement Gel every time
- Release vacuum via the valve before removing
- Limit sessions to 15–20 minutes max
- Remove constriction ring within 30 minutes
- Stop immediately if you feel pain
⛔ Don't
- Don't jump to maximum suction immediately
- Don't use oil or silicone-based lubes
- Don't pull the cylinder off without releasing pressure
- Don't exceed 20 minutes of continuous use
- Don't wear the ring overnight or during sleep
- Don't push through discomfort
When NOT to Use — Consult a Doctor First If You:
⚕️ Speak with your healthcare provider before use if any of the following apply:
- Take blood thinners (warfarin, aspirin therapy, etc.)
- Have a bleeding or clotting disorder
- Have sickle cell anemia
- Have Peyronie's disease (curved erections with scar tissue)
- Have had recent penile surgery
- Have a history of priapism (prolonged, painful erections)
Troubleshooting
Problem
Vacuum won't build
Solution
Check that the silicone seal is flush against skin; reapply lubricant or Intimacy Enhancement Gel
Problem
Device won't turn on
Solution
Recharge via USB; check cable connection
Problem
Weak suction
Solution
Charge the battery; check seal for cracks or wear
Problem
Discomfort or pain
Solution
Reduce pressure using the − button or press the release valve immediately
Problem
Bruising or red spots
Solution
Stop use and rest. Consult a doctor if symptoms persist.
Problem
Ring difficult to remove
Solution
Apply water-based lubricant or Intimacy Enhancement Gel around the ring and gently roll it off
Have additional questions?
Our support team is here to help you get the most out of your MaxiFirm Pro.
Contact Support →